Like promised in my post above, which is full of typo's a bootlog
the minidlna stuff is known problem. I still have to make the drive mount at startup.
Connected.
Stage-1 Bootloader 2012-06.13-13:06:32
Attempting to set PLLA to 750MHz ...
plla_ctrl0 : 0x0000000A
plla_ctrl1 : 0x000F0000
plla_ctrl2 : 0x001D01A0
plla_ctrl3 : 0x00000017
PLLA Set
Setup memory, testing, Image 0
Hdr len: 0x00028594
Hdr CRC: 0x0BA1B9D0
OK
_ _ _ _
| | | | | | | |
___| |__ _ _| |_| |_| | ___
/ __| '_ \| | | | __| __| |/ _ \
\__ \ | | | |_| | |_| |_| | __/
|___/_| |_|\__,_|\__|\__|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
U-Boot 1.1.2 (Oct 22 2012 - 10:55:50)
U-Boot code: 60D00000 -> 60D28594 BSS: -> 60D3B2C0
IRQ Stack: 60cddf7c
FIQ Stack: 60cdcf7c
RAM Configuration:
Bank #0: 60000000 256 MB
SRAM Configuration:
64KB at 0x50000000
NAND:128 MiB
In: serial
Out: serial
Err: serial
Initialising disks
OX820 SATA Init...
SATA PHY not ready for device 1
Detecting SATA busses:
Bus 0: Found first device OK
Device 0: Model: WDC WD30EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WCC4N0748799
Type: Hard Disk
Supports 48-bit addressing
Capacity: 764436.4 MB = 746.5 GB (1565565872 x 512)
Device 1: not available
Setting Linux mem= boot arg value
Hit any key to stop autoboot: 0
Device 0: 128MiB 3,3V 8-bit, sector size 128 KB
NAND read: device 0 offset 0x840000, size 0x350000
Reading data from 0xb8f800 -- 100% complete.
3473408 bytes read: OK
NAND read: device 0 offset 0x240000, size 0x280000
Reading data from 0x4bf800 -- 100% complete.
2621440 bytes read: OK
## Booting image at 60500000 ...
Image Name: Linux-3.18.1_7
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3066491 Bytes = 2.9 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 64000000 ...
Image Name: Wheezy Ramdisk
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1841056 Bytes = 1.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.18.1_KD20-peace (peacemaker@VBarch) (gcc version 4.9.1 (GCC) ) #14 SMP Mon Jan 5 11:17:33 CET 2015
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Shuttle KD20
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 9 pages/cpu @cfde0000 s6784 r8192 d21888 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sdb2 console=ttyS0,115200 mem=256M poweroutage=yes
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 249248K/262144K available (6197K kernel code, 241K rwdata, 1680K rodata, 184K init, 392K bss, 12896K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07b965c (7878 kB)
[ 0.000000] .init : 0xc07ba000 - 0xc07e8000 ( 184 kB)
[ 0.000000] .data : 0xc07e8000 - 0xc08247d0 ( 242 kB)
[ 0.000000] .bss : 0xc08247d0 - 0xc08869ec ( 393 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000020] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 42949670400ns
[ 0.000235] Console: colour dummy device 80x30
[ 0.000266] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[ 0.069936] pid_max: default: 32768 minimum: 301
[ 0.070138] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070161] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.071080] CPU: Testing write buffer coherency: ok
[ 0.071513] Setting up static identity map for 0x605e5dc8 - 0x605e5e00
[ 0.073551] CPU1: Booted secondary processor
[ 0.140152] Brought up 2 CPUs
[ 0.140177] SMP: Total of 2 processors activated.
[ 0.141222] devtmpfs: initialized
[ 0.144862] xor: measuring software checksum speed
[ 0.239976] arm4regs : 1039.200 MB/sec
[ 0.339975] 8regs : 482.800 MB/sec
[ 0.439971] 32regs : 526.000 MB/sec
[ 0.439989] xor: using function: arm4regs (1039.200 MB/sec)
[ 0.440038] pinctrl core: initialized pinctrl subsystem
[ 0.443038] NET: Registered protocol family 16
[ 0.443727] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.448058] gpio-oxnas 44000000.gpio: at address d0848000
[ 0.448345] gpio-oxnas 44100000.gpio: at address d084a000
[ 0.448791] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.620695] raid6: int32x1 37 MB/s
[ 0.790097] raid6: int32x2 60 MB/s
[ 0.960222] raid6: int32x4 66 MB/s
[ 1.130355] raid6: int32x8 65 MB/s
[ 1.130375] raid6: using algorithm int32x4 (66 MB/s)
[ 1.130388] raid6: using intx1 recovery algorithm
[ 1.240985] oxnas-pcie 47c0: PCIe version/deviceID 0x82510b5
[ 1.252032] oxnas-pcie 47c0: link up
[ 1.252282] oxnas-pcie 47c0: PCI host bridge to bus 0000:00
[ 1.252313] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[ 1.252336] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[ 1.252359] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
[ 1.252382] pci_bus 0000:00: root bus resource [bus 00-7f]
[ 1.252922] PCI: bus0: Fast back to back transfers disabled
[ 1.253009] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x48007fff 64bit]
[ 1.253432] vgaarb: loaded
[ 1.253962] SCSI subsystem initialized
[ 1.254773] usbcore: registered new interface driver usbfs
[ 1.254878] usbcore: registered new interface driver hub
[ 1.255019] usbcore: registered new device driver usb
[ 1.255162] pps_core: LinuxPPS API ver. 1 registered
[ 1.255178] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.255221] PTP clock support registered
[ 1.256896] cfg80211: Calling CRDA to update world regulatory domain
[ 1.257297] Switched to clocksource rps_clocksource_timer
[ 1.271539] NET: Registered protocol family 2
[ 1.272601] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.272663] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 1.272729] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.272821] TCP: reno registered
[ 1.272852] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.272898] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.273231] NET: Registered protocol family 1
[ 1.273871] RPC: Registered named UNIX socket transport module.
[ 1.273894] RPC: Registered udp transport module.
[ 1.273907] RPC: Registered tcp transport module.
[ 1.273917] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.273991] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 1.274472] Unpacking initramfs...
[ 1.489044] Freeing initrd memory: 1800K (c4000000 - c41c2000)
[ 1.490342] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 1.506961] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.508815] fuse init (API version 7.23)
[ 1.509672] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 1.513758] NILFS version 2 loaded
[ 1.515955] gfs2: GFS2 installed
[ 1.516026] msgmni has been set to 490
[ 1.519329] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.519367] io scheduler noop registered
[ 1.519390] io scheduler deadline registered
[ 1.519454] io scheduler cfq registered (default)
[ 1.520053] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.521413] console [ttyS0] disabled
[ 1.521495] of_serial 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[ 2.094159] console [ttyS0] enabled
[ 2.100224] scsi host0: sata_oxnas
[ 2.104330] scsi host1: sata_oxnas
[ 2.108060] ata1: SATA max UDMA/133 irq 50
[ 2.112268] ata2: SATA max UDMA/133 irq 50
[ 2.117639] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 2.124008] nand: Hynix H27U1G8F2BTR-BC
[ 2.127831] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 2.133488] Scanning device for bad blocks
[ 2.143823] sata_oxnas: resetting SATA core
[ 2.157557] Bad eraseblock 243 at 0x000001e60000
[ 2.191459] Bad eraseblock 600 at 0x000004b00000
[ 2.229143] Bad eraseblock 1004 at 0x000007d80000
[ 2.235422] 2 ofpart partitions found on MTD device 41000000.nand
[ 2.241510] Creating 2 MTD partitions on "41000000.nand":
[ 2.246886] 0x000000000000-0x000000e00000 : "boot"
[ 2.253214] 0x000000e00000-0x000008000000 : "ubi"
[ 2.259860] stmmaceth 40400000.ethernet: snps,phy-addr property is deprecated
[ 2.267125] stmmaceth 40400000.ethernet: no reset control found
[ 2.273054] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 2.278074] Ring mode enabled
[ 2.281128] DMA HW capability register supported
[ 2.285634] Enhanced/Alternate descriptors
[ 2.289981] Enabled extended descriptors
[ 2.293972] RX Checksum Offload Engine supported (type 2)
[ 2.299425] TX Checksum insertion supported
[ 2.303685] Wake-Up On Lan supported
[ 2.307328] Enable RX Mitigation via HW Watchdog Timer
[ 2.326000] libphy: stmmac: probed
[ 2.329400] eth0: PHY ID 02430d91 at 1 IRQ POLL (stmmac-0:01) active
[ 2.336074] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.342620] ehci-pci: EHCI PCI platform driver
[ 2.347392] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 2.352939] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 2.360744] oxnas-ehci 40200100.ehci: irq 39, io mem 0x40200100
[ 2.380024] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 2.386373] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.393182] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.400424] usb usb1: Product: EHCI Host Controller
[ 2.405283] usb usb1: Manufacturer: Linux 3.18.1_KD20-peace ehci_hcd
[ 2.411630] usb usb1: SerialNumber: 40200100.ehci
[ 2.417223] hub 1-0:1.0: USB hub found
[ 2.421086] hub 1-0:1.0: 2 ports detected
[ 2.425804] usbcore: registered new interface driver usblp
[ 2.431485] usbcore: registered new interface driver usb-storage
[ 2.437821] mousedev: PS/2 mouse device common for all mice
[ 2.443827] gpio-fan gpio-fan: GPIO fan initialized
[ 2.448757] md: linear personality registered for level -1
[ 2.454292] md: raid0 personality registered for level 0
[ 2.459591] md: raid1 personality registered for level 1
[ 2.464908] md: raid10 personality registered for level 10
[ 2.471331] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: dm-devel@redhat.com
[ 2.481602] usbcore: registered new interface driver usbhid
[ 2.487152] usbhid: USB HID core driver
[ 2.491397] TCP: cubic registered
[ 2.495795] NET: Registered protocol family 10
[ 2.501990] sit: IPv6 over IPv4 tunneling driver
[ 2.507535] NET: Registered protocol family 17
[ 2.517066] Btrfs loaded
[ 2.520143] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.653667] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2.660400] ata1.00: ATA-9: WDC WD30EZRX-00D8PB0, 80.00A80, max UDMA/133
[ 2.667107] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 2.674383] ata1.00: configured for UDMA/133
[ 2.679180] scsi 0:0:0:0: Direct-Access ATA WDC WD30EZRX-00D 0A80 PQ: 0 ANSI: 5
[ 2.689011] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 2.696793] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.702095] sata_oxnas: resetting SATA core
[ 2.710479] sd 0:0:0:0: [sda] Write Protect is off
[ 2.715502] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.733762] sata_oxnas: resetting SATA core
[ 2.740106] usb 1-2: new high-speed USB device number 2 using oxnas-ehci
[ 2.897930] usb 1-2: New USB device found, idVendor=058f, idProduct=6387
[ 2.904668] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.911810] usb 1-2: Product: Mass Storage
[ 2.915893] usb 1-2: Manufacturer: Generic
[ 2.919989] usb 1-2: SerialNumber: 7E518F6A
[ 2.925217] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 2.931932] scsi host2: usb-storage 1-2:1.0
[ 3.413670] ata2: SATA link down (SStatus 0 SControl 310)
[ 3.493667] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[ 3.500533] ata1: hard resetting link
[ 3.932316] scsi 2:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 4
[ 3.943370] sd 2:0:0:0: [sdb] 15974400 512-byte logical blocks: (8.17 GB/7.61 GiB)
[ 3.951982] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.957731] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.023864] sdb: sdb1 sdb2
[ 4.031367] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 4.413665] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 4.420997] ata1.00: configured for UDMA/133
[ 4.425300] ata1: EH complete
[ 5.189854] sda: sda1 sda2 sda3 sda4
[ 5.196257] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.201292] Freeing unused kernel memory: 184K (c07ba000 - c07e8000)
Loading, please wait...
[ 5.351846] udevd[89]: starting version 175
modprobe: chdir(3.18.1_KD20-peace): No such file or directory
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
modprobe: chdir(3.18.1_KD20-peace): No such file or directory
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 8.895188] random: nonblocking pool is initialized
[ 8.938055] udevd[293]: starting version 175
. ok
[ ok ] Synthesizing the initial hotplug events...done.
[ ok ] Waiting for /dev to be fully populated...done.
[ ok ] Activating swap...done.
[ 11.608709] EXT2-fs (sdb2): warning: mounting unchecked fs, running e2fsck is recommended
[ ok ] Cleaning up temporary files... /tmp.
[info] Loading kernel module mii.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module gmac.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module scsi_wait_scan.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module ahci.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module led-class.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module ledtrig-backlight.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module ledtrig-default-on.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module ledtrig-heartbeat.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module mmc_block.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module mmc_core.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module sdhci-pci.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module sdhci-pltfm.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module sdhci.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module spi_bitbang.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module spi_ox820_gpio.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module usblp.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[info] Loading kernel module autofs4.
libkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/3.18.1_KD20-peace/modules.dep.bin'
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.20.1
done.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[ ok ] Configuring network interfaces...done.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting enhanced syslogd: rsyslogd[ 22.793835] stmmaceth 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[2015/04/28 16:50:16] minidlna.c:474: error: Media directory "/storage/media/fotos" not accessible! [No such file or directory]
[2015/04/28 16:50:16] minidlna.c:474: error: Media directory "/storage/media/movies" not accessible! [No such file or directory]
[2015/04/28 16:50:16] minidlna.c:474: error: Media directory "/storage/media/tv" not accessible! [No such file or directory]
[2015/04/28 16:50:16] minidlna.c:474: error: Media directory "/storage/media/concerts" not accessible! [No such file or directory]
[2015/04/28 16:50:16] utils.c:265: warn: make_dir: cannot create directory '/storage/.cache/'
[2015/04/28 16:50:16] minidlna.c:529: fatal: Database path not accessible! [/storage/.cache/minidlna]
Debian GNU/Linux 7 oxnas ttyS0
oxnas login:
the minidlna stuff is known problem. I still have to make the drive mount at startup.