Re: Debian on Shuttle KD20 (PLX OXNAS 7821)
Hm,.. Okay, then software is not the problem here, or at least not the software on KD20. Can you somehow check if your UART/Serial equipment is working properly?
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
UART converter/serial is working properly on other device - Zyxel NSA310
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
I think you checked the connectors on the KD20 board, as well :-) But some how I'm out of idea for now where the problem with console can be. I
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Ok, it was problem with connectivity between pins and mainboard... How to repair console permanently? Can you share me files for booting debian from disk?
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Jacq Wrote: ------------------------------------------------------- > Can you share me files for booting debian from > disk? Sry, at the moment a full sata boot did'nt work. As Uboot did not...
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Jacq Wrote: ------------------------------------------------------- > Ok, it was problem with connectivity between pins > and mainboard... You should know, how to fix the contacts :-) Try to...
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
When i remove prepared disk from the omninas uboot isn't loading(from nand)....
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Okay, then 1. boot form sata to Uboot 2. load your uboot-backup via tftp tftp 64000000 uboot.backup # <- your backup file former mtd2 3. write it back to nand: nand erase 40000 200000 nand write...
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
After download this two files and remove the disk: _ _ _ _ | | | | | | | | ___| |__ _ _| |_| |_| | ___ / __| '_ \| | | | __| __| |/ _ \ \__ \ | | | |_| | |_| |_| | __/ |___/_| |_|\__,_|\__|\__|_|\___|...
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Stage1 is OK. But it did not find your uboot, so maybe try to flash again the uboot. If it fails i'll check my files again.
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Where can i find file rdimg.gz? Is it for omninas?
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
After trying to get a USB to serial converter working under the original firmware. I've managed to f*ck up the kernel and not getting it to boot at all. After follwing Peacemakers instructions I've...
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Like promised in my post above, which is full of typo's a bootlog Connected. Stage-1 Bootloader 2012-06.13-13:06:32 Attempting to set PLLA to 750MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000F0000...
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Hey, First, I some how have stopped (maybe stalled) to look deeper into the KD20 as I have at the moment not the time and efford to do so (and have a good working debian NAS RN102) @Fritsbenik So one...
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
@Peacemaker Is it possible for you to upload the sources. The one in your dropbox is for a older kernel. I didn't have time to look at the LED classes yet.
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Regarding serial, anyone care to share the pin layout of CON5, need to find the RX/TX and the gitorious link is down. Thanks, Xander
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
1. RX normally has pull up/down resistor. 2. TX will have signal out during booting.
View ArticleRe: Debian on Shuttle KD20 (PLX OXNAS 7821)
Odd, I need RX and TX to be both connected to get serial messages, so I see booting but I am unable to interrupt u-boot or login from the console. minicom settings are 115200 baud 8N1 identical...
View Article